Tecno R-evolution

Turbix
cyclonic pre-separator

The cyclonic separators of the Turbix line are recommended in cases where aspiration of large quantities of dust are required, especially fine dust, to intercept and break them down, avoiding large scale deposits on filter walls, with the consequent reduction of suction power and the need for frequent maintenance. They are available in three different sizes, depending on the suction unit and the connetion line diameter.

Installation parameters

With Turbix it is possible to vacuum:

  • Leaves and soil
  • Sand / fine powders
  • Hair / animal hair
  • Flour
  • Wood chips and sawdust
MODEL Imbocchi ARTICLE Max number
IN/OUT ømm of operators
Turbix SMALL 50mm 3400.10 2
Turbix MEDIUM 63mm 3400.11 3
Turbix BIG 80mm 3400.12 4

Great efficiency

No filter

Large dust collection capacity

Great efficiency

The capacity to deal with aspirated powders is exceptional: in some cases the effectiveness reaches more than 98% of the total amount sucked. The secret is due to the particular shape of the cone, which gives the vacuumed powders a cyclonic motion with increasing speed as the cone narrows. At the end of the cone, when the air flows into the dust collecting bucket, it slows down and allows the dust to fall to the bottom of the bucket, while the clean air will continue its path out.

No filter

The special Turbix separators do not have a filter inside, therefore the only maintenance required is to empty the powder container when it fills up. A guarantee of effectiveness, but above all a considerable simplification in maintenance.

Feature shortlist

  • Self-supporting cylindrical shell in epoxy powder coated metal

  • Polypropylene dust collection bin (Turbix Small model, capacity 21L)

  • Epoxy powder painted metal dust collection bucket (model Turbix Medium; capacity 40L)

  • Turbix Big metal powder container (capacity 70L) with wheels for handling

  • Possibility of left/right orientation for inlet and outlet tube connections

Tecno R-evolution

Separator with automatic discharge
Auto Jet Turbix

Auto Jet Turbix is ​​a unique product of its kind: the presence of the cyclonic effect cone allows it to have an extraordinary powder handling capacity, preventing them from clogging the filter of the central vacuum unit, while the automatic discharge device makes it suitable for high volume material suction, without the need for continuous collection vessel emptying.

Installation parameters

It is recommended to install the AUTO Jet Turbix in environments where high dust volume suction, even particularly fine dust is required.
When continuous use of the suction system is required, the collected powders can be dumped into containers of various types and sizes, even without turning off the suction system.

The AUTO Jet Turbix must be used in combination with one or more blower motors, with systems configured for air flow up to 400 m3 / h.

These components are used for installations with the following characteristics:

  • Ø 63/80 mm upright column
  • Dust input Ø 80 mm
  • Option of using the system up to a recommended 2 operators;
MODEL Imbocchi ARTICLE Max number
IN/OUT ømm of operators
Turbix SMALL 50mm 3400.10 2
Turbix MEDIUM 63mm 3400.11 3
Turbix BIG 80mm 3400.12 4

Probes for air jets

Control panel

Door with pneumatic opening

Easy drain

To facilitate the discharge of any type of collected material, even the lightest and most voluminous ones, the separator is equipped with 8 nozzles that allow the discharge of compressed air when the lower door is opened.
The flow of compressed air is guaranteed by the 3/4″ connection, which is connected to an external pneumatic supply line.

Simplicity of Programing

Thanks to the three potentiometers on the control panel it is possible to adjust the following operating parameters:

  • suction time (to avoid overfilling the container)
  • opening time of the door (to be set according to the specific weight and consistency of the collected material)
  • repetition of the compressed air jets which act during discharge.

Using the TEST button it is possible to test each of these three settings immediately, to find the optimal setting, according to the quantity and type of vacuumed material.

Feature shortlist

  • Supporting structure in epoxy powder coated steel

  • Cyclone body in stainless steel

  • Suitable for vacuuming both solids and liquids

  • Option of connecting 8 nozzles that can be supplied with compressed air

  • Blowing system control panel, powder filling and dust discharge adjustable by potentiometer